Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: G Sensor Failure (C1647)

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Audio & Visual & Telematics / Park Assist / Monitoring / Intelligent Clearance Sonar System / G Sensor Failure (C1647)

DESCRIPTION

The clearance warning sonar ECU assembly communicates with the airbag sensor assembly*1 or yaw rate and acceleration sensor*2 via CAN communication, and if it is determined that the airbag sensor assembly*1 or yaw rate and acceleration sensor*2 is malfunctioning, DTC C1647 is stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1647

G Sensor Failure

Airbag sensor assembly*1 or yaw rate and acceleration sensor*2 malfunction

Vehicle stability control system
  • *1: for Optitron Meter Type
  • *2: for TFT Meter Type

CAUTION / NOTICE / HINT

NOTICE:

  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • After replacing an ultrasonic sensor or the clearance warning ECU assembly, perform the necessary procedures (adjustment, calibration, initialization or registration).

    Click here

PROCEDURE

1.

CHECK DTC OUTPUT

(a) Using the Techstream, check for DTCs according to the prompts on the screen.

Click here

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Trouble Codes

(b) Clear the DTCs according to the screen on the Techstream.

Click here

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Clear DTCs

(c) Recheck for DTCs.

Click here

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Trouble Codes

HINT:

  • DTC C1647 is stored when a malfunction signal sent from the vehicle stability control system is detected.
  • If the malfunctioning part has been repaired or replaced before rechecking for DTCs, DTC C1647 will not be output again.
  • If DTC C1647 is output frequently, duplicate the conditions that cause the problem symptoms and perform the inspection again, even though the DTC was not output when rechecking for DTCs.

    Click here

Result

Proceed to

DTC C1647 is output

A

DTC C1647 is not output

B
A

GO TO VEHICLE STABILITY CONTROL SYSTEM

B

USE SIMULATION METHOD TO CHECK

    Communication Error From Clearance Sonar ECU to VSC (C164B)
    DESCRIPTION The vehicle stability control system receives intelligent clearance sonar system information from the clearance warning ECU assembly via CAN communication. When it is determined that there ...

    Wheel Speed Sensor Malfunction (C164D)
    DESCRIPTION This DTC is stored when the clearance warning ECU assembly receives a wheel speed sensor (front speed sensor RH or front speed sensor LH, rear speed sensor RH or rear speed sensor LH) abno ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Cruise Control Main Switch: Installation
    INSTALLATION PROCEDURE 1. INSTALL CRUISE CONTROL MAIN SWITCH (a) Connect the connector. (b) Pass the cruise control switch wire under the rib as shown in the illustration, and temporarily install the cruise control main switch with the 2 screws. *1 Cruise Control Switch Wire *a ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Vehicle Stability Control System: Freeze Frame Data
    FREEZE FRAME DATA FREEZE FRAME DATA (a) Using the Techstream, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output. CHECK FREEZE FRAME DATA WHEN DTC WAS STORED HINT: Freeze frame data is stored when a DTC is output. Once freeze frame data is stored when a ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0137