Lexus RX (RX 350L, RX450h) 2016-2023 Repair Manual: Inspection

INSPECTION

PROCEDURE

1. INSPECT SHIFT SOLENOID VALVE S1

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body

20°C (68°F)

11 to 15 Ω

If the result is not as specified, replace the shift solenoid valve S1.

*a

Component without harness connected

(Shift Solenoid Valve S1)

(b) Connect a positive (+) lead from the battery to the terminal of the shift solenoid valve S1 connector and a negative (-) lead to the shift solenoid valve S1 body, and check that the shift solenoid valve S1 moves and makes an operating sound.

NOTICE:

When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

OK:

The shift solenoid valve S1 moves and makes an operating sound.

If the result is not as specified, replace the shift solenoid valve S1.

2. INSPECT SHIFT SOLENOID VALVE S2

HINT:

Refer to Inspect Shift Solenoid Valve S1.

3. INSPECT SHIFT SOLENOID VALVE SLU

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 - 2

20°C (68°F)

5.0 to 5.6 Ω

If the result is not as specified, replace the shift solenoid valve SLU.

*a

Component without harness connected

(Shift Solenoid Valve SLU)

(b) Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the shift solenoid valve SLU connector, and check that the shift solenoid valve SLU moves and makes an operating sound.

NOTICE:

When using battery voltage during the inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.

OK:

The shift solenoid valve SLU moves and makes an operating sound.

If the result is not as specified, replace the shift solenoid valve SLU.

4. INSPECT SHIFT SOLENOID VALVE SL1

HINT:

Refer to Inspect Shift Solenoid Valve SLU.

5. INSPECT SHIFT SOLENOID VALVE SL2

HINT:

Refer to Inspect Shift Solenoid Valve SLU.

6. INSPECT SHIFT SOLENOID VALVE SL3

HINT:

Refer to Inspect Shift Solenoid Valve SLU.

7. INSPECT SHIFT SOLENOID VALVE SL4

HINT:

Refer to Inspect Shift Solenoid Valve SLU.

8. INSPECT SHIFT SOLENOID VALVE SL5

HINT:

Refer to Inspect Shift Solenoid Valve SLU.

9. INSPECT SHIFT SOLENOID VALVE SLT

HINT:

Refer to Inspect Shift Solenoid Valve SLU.

    Disassembly
    DISASSEMBLY PROCEDURE 1. REMOVE MANUAL VALVE (a) Remove the manual valve from the transmission valve body assembly. (b) Remove the E-ring and separate the manual valve connecting rod ...

    Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during tran ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2023 Repair Manual > Lumbar Switch: Installation
    INSTALLATION CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the parts may injure your hands. HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. INSTALL FRONT LUMBAR POWER SEAT SWITCH (a) Engage the 4 ...

    Lexus RX (RX 350L, RX450h) 2016-2023 Repair Manual > Wiper And Washer System: Terminals Of Ecu
    TERMINALS OF ECU CHECK WINDSHIELD WIPER MOTOR ASSEMBLY (a) Disconnect the i1 windshield wiper motor assembly connector. (b) Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below. Terminal No. (Symbol) Wiring Color Terminal Descript ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    Chevrolet Trax (2013-2022) Owner's Manual

    © 2023 Copyright www.lexusrx.net
    0.0198