Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Inspection

INSPECTION

PROCEDURE

1. INSPECT GENERATOR PULLEY WITH CLUTCH

(a) Hold the center of the generator pulley with clutch, and confirm that the outer ring turns counterclockwise and does not turn clockwise.

OK:

The outer ring turns counterclockwise and does not turn clockwise.

If the result is not as specified, replace the generator pulley with clutch.

Free

Lock

2. INSPECT GENERATOR BRUSH HOLDER ASSEMBLY

(a) Using a vernier caliper, measure the length of the exposed brushes.

Standard Exposed Brush Length:

9.5 to 11.5 mm (0.374 to 0.453 in.)

Minimum Exposed Brush Length:

4.5 mm (0.177 in.)

If the brush length is less than the minimum, replace the generator brush holder assembly.

*a

Length

3. INSPECT GENERATOR ROTOR ASSEMBLY

(a) Check the generator rotor assembly for an open circuit.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Slip ring - Slip ring

20°C (68°F)

1.9 to 2.3 Ω

If the result is not as specified, replace the generator rotor assembly.

*a

Slip Ring

(b) Check the generator rotor assembly for a short to ground.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Slip ring - Rotor

Always

1 MΩ or higher

If the result is not as specified, replace the generator rotor assembly.

*a

Slip Ring

*b

Rotor

(c) Check that the generator rotor bearing is not rough or worn and that it rotates smoothly.

If the generator rotor bearing is rough or worn, or does not rotate smoothly, replace the generator rotor assembly.

(d) Check the slip ring.

(1) Check that the slip rings are not rough or scored.

If the slip rings are rough or scored, replace the generator rotor assembly.

(2) Using a vernier caliper, measure the slip ring diameter.

Standard Diameter:

14.2 to 14.8 mm (0.559 to 0.583 in.)

Minimum Diameter:

14.0 mm (0.551 in.)

If the diameter is less than the minimum, replace the generator rotor assembly.

*a

Diameter

4. INSPECT GENERATOR DRIVE END FRAME BEARING

(a) Check that the generator drive end frame bearing is not rough or worn and that it rotates smoothly.

If the generator drive end frame bearing is rough or worn, or does not rotate smoothly, replace the generator drive end frame bearing.

    Disassembly
    DISASSEMBLY PROCEDURE 1. REMOVE GENERATOR PULLEY CAP (a) Using a screwdriver, remove the generator pulley cap from the generator pulley with clutch. NOTICE: Do not reuse the generator pulley cap. ...

    Installation
    INSTALLATION PROCEDURE 1. INSTALL GENERATOR ASSEMBLY (a) Install the wire harness clamp bracket with the bolt. Torque: 8.4 N·m {86 kgf·cm, 74 in·lbf} (b) Type A: (1) Install the generator assembly ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Generator (for 150 A Type): Reassembly
    REASSEMBLY PROCEDURE 1. INSTALL GENERATOR DRIVE END FRAME BEARING (a) Using SST and a press, install a new generator drive end frame bearing. SST: 09950-60010 09951-00470 SST: 09950-70010 09951-07100 (b) Fit the tabs of the retainer plate into the cutouts of the generator drive end ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Wiper And Washer System: Lost Communication with Wiper ECU LIN (B1245)
    DESCRIPTION The main body ECU (multiplex network body ECU) and windshield wiper motor and link assembly communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal. DTC No. Detection Item DTC Detection Condition Trouble ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0148