Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Center Airbag Sensor Communication Stop Mode

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Power Source & Network / Networking / Can Communication System / Center Airbag Sensor Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Center Airbag Sensor Communication Stop Mode

Either condition is met:

  • "Airbag" is not displayed on the CAN Bus Check screen of the Techstream.

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "Center Airbag Sensor Communication Stop Mode" in "DTC Combination Table" are output.

    Click here

  • Airbag sensor assembly main line or connector
  • Power source circuit of airbag sensor assembly
  • Airbag sensor assembly ground circuit
  • Airbag sensor assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

  • Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the engine switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.

CHECK FOR OPEN IN CAN BUS LINES (AIRBAG SENSOR ASSEMBLY MAIN LINE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the J142 airbag sensor assembly connector.

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

J142-26 (CANH) - J142-27 (CANL)

Cable disconnected from negative (-) battery terminal

108 to 132 Ω
NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (AIRBAG SENSOR ASSEMBLY)
OK

2.

CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

J142-32 (E2) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

J142-33 (E1) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

(b) Reconnect the cable to the negative (-) battery terminal.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

J142-36 (IG2) - Body ground

Engine switch on (IG)

11 to 14 V
OK

REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
    ECM Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area ECM Communication Stop Mode Either condition is met: "ECM (Engine)" is not displayed on the CAN Bus Check screen of the Techstream. Clic ...

    Certification ECU Communication Stop Mode
    DESCRIPTION Detection Item Symptom Trouble Area Certification ECU Communication Stop Mode Either condition is met: "Certification (Smart)" is not displayed on the CAN Bus Check screen ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Power Steering Ecu: Components
    COMPONENTS ILLUSTRATION *1 ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY *2 POWER STEERING ECU ASSEMBLY *3 ELECTRIC POWER STEERING MOTOR SHAFT DAMPER *4 STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY *5 STEERING LOCK SET BOLT - - N*m (kgf*cm, ft.*lbf): Specified ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Navigation System: Terminals Of Ecu
    TERMINALS OF ECU HINT: Check from the rear of the connector while it is connected to the components. RADIO RECEIVER ASSEMBLY Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition *: It is connected, but not used J151-1 (VMTF) - J148-1 (GND1) Y - ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0187