Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Inspection

Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual / Power Source & Network / Power Distribution / Integration Relay / Inspection

INSPECTION

PROCEDURE

1. INSPECT SEMICONDUCTOR POWER INTEGRATION ECU

(a) IG2 RELAY:

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

B-1 - 1F-4

Battery voltage not applied between terminals 1E-1 and 1D-14

10 kΩ or higher

B-1 - 1G-3

B-1 - 1G-4

B-1 - 1F-4

Battery positive (+) → 1E-1

Battery negative (-) → 1D-14

Below 1 Ω

B-1 - 1G-3

B-1 - 1G-4

If the result is not as specified, replace the semiconductor power integration ECU.

*a

Component without harness connected

(Semiconductor Power Integration ECU)

(b) EFI-MAIN RELAY:

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

B-1 - 1G-1

Battery voltage not applied between terminals 1G-6 and 1D-14

10 kΩ or higher

B-1 - 1G-2

B-1 - 1G-7

B-1 - 1G-8

1F-2 - 1G-1

B-1 - 1G-1

Battery positive (+) → 1G-6

Battery negative (-) → 1D-14

Below 1 Ω

B-1 - 1G-2

B-1 - 1G-7

B-1 - 1G-8

1F-2 - 1G-1

If the result is not as specified, replace the semiconductor power integration ECU.

*a

Component without harness connected

(Semiconductor Power Integration ECU)

(c) A/F RELAY:

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

B-1 - 1F-1

Battery voltage not applied between terminals 1G-1 and 1D-14

10 kΩ or higher

B-1 - 1F-1

Battery positive (+) → 1G-1

Battery negative (-) → 1D-14

Below 1 Ω

If the result is not as specified, replace the semiconductor power integration ECU.

*a

Component without harness connected

(Semiconductor Power Integration ECU)

(d) H-LP RH-LO RELAY:

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

B-1 - 1E-2

Battery voltage not applied between terminals B-1 and 1D-8

10 kΩ or higher

*a

Component without harness connected

(Semiconductor Power Integration ECU)

(2) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

1E-2 - Battery negative (-)

Battery positive (+) → B-1

Battery negative (-) → 1D-8

11 to 14 V

If the result is not as specified, replace the semiconductor power integration ECU.

(e) H-LP LH-LO RELAY:

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

B-1 - 1E-3

Battery voltage not applied between terminals B-1 and 1D-8

10 kΩ or higher

*a

Component without harness connected

(Semiconductor Power Integration ECU)

(2) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

1E-3 - Battery negative (-)

Battery positive (+) → B-1

Battery negative (-) → 1D-8

11 to 14 V

If the result is not as specified, replace the semiconductor power integration ECU.

(f) Semiconductor power integration ECU ground:

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1D-14 - 1G-5

Always

Below 1 Ω

If the result is not as specified, replace the semiconductor power integration ECU.

*a

Component without harness connected

(Semiconductor Power Integration ECU)
    Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during int ...

    Installation
    INSTALLATION PROCEDURE 1. INSTALL SEMICONDUCTOR POWER INTEGRATION ECU (a) Connect the 5 connectors. (b) Engage the 2 claws to install the semiconductor power integration ECU as shown in the illustrati ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Transfer Assembly: Disassembly
    DISASSEMBLY CAUTION / NOTICE / HINT NOTICE: Before installation of each part, thoroughly clean and dry it. Then apply grease or oil as necessary. Do not use alkaline chemicals to clean aluminum parts, rubber parts or precoated bolts. Also, do not use non-residue solvent or other cleaning oils to cle ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Headlight Ecu: Installation
    INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. INSTALL HEADLIGHT GASKET (a) Install a new headlight gasket. 2. INSTALL NO. 1 HEADLIGHT ECU SUB-ASSEMBLY NOTICE: If the No. 1 headlight ligh ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0153