FREEZE FRAME DATA
FREEZE FRAME DATA
(a) Whenever a DTC is detected, the multiplex network door ECU stores the current vehicle state as Freeze Frame Data.
CHECK FREEZE FRAME DATA
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Back Door / Trouble Codes.
Body Electrical > Back Door| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Half Latch SW | Half-latch switch signal | OFF or ON | OFF: Back door lock motor in full latch or half latch position ON: Back door lock motor in open latch position | - |
| Closer Position SW | Position switch signal | OFF or ON | OFF: Back door lock center gear out of center position(Position switch off) ON: Back door lock center gear in center position (Position switch on) | - |
| Pawl Position Switch | Pawl position switch signal | OFF or ON | OFF: Back door lock motor except open latched ON: Back door lock motor open latched | - |
| Courtesy SW | Back door courtesy switch signal | OFF or ON | OFF: Back door closed ON: Back door open | - |
| Back Door Position | Status of the back door position | -4000 to 21500 Edge | 3000 to 6000 Edge | - |
| Back Door Horizontal Torsion | Status of the torsion between back door LH and RH | -128 to 127 Edge | -128 to 127 Edge | - |
| Battery Voltage | Status of the battery voltage | 0 to 31 V | 11 to 14 V | - |
| Closer Control Status | Status of the closer control | Initialize, Close 1: Standby, Close 2: Operate Standby, Close 3: Operation, Close 4: Return Standby, Close 5: Return, Release 1: Standby, Release 2: Operation, Release 3: Return Standby, Release 4: Return, Forcible 1: Release Operation, Forcible 2: Close Standby, Forcible 3: Close Operation Standby, Forcible 4: Close Operation, Forcible 5: Closer Torque Moderate, Forcible 6: Door Check or Stop Function | Status of the closer control | - |
| PBD Control Status | Status of the power back door system control | All Close Initialize, All Close, Open 1: Auto Open Standby, Open 2: Latch Release Standby, Open 3: Auto Open Operation, All Open, Close 1: Auto Close Standby, Close 2: Auto Close Operation, Close 3: Closer Start Standby, Close 4: All Close Standby, Neutral, Auto Close Reverse or Brake | Status of the power back door system control | - |
| #Codes | Number of DTCs | Min.: 0, Max.: 255 | Number of DTCs will be displayed | - |
CLEAR FREEZE FRAME DATA
NOTICE:
Clearing the DTCs will also clear the Freeze Frame Data.
(a) Turn the engine switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the engine switch on (IG).
(d) Turn the Techstream on.
(e) Clear the DTCs and Freeze Frame Data.
Dtc Check / Clear
Terminals Of EcuLexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Can Communication System: Open in One Side of Bus 4 Branch Line
DESCRIPTION If an ECU or sensor is not displayed on the CAN Bus Check screen of the Techstream and some ECUs and sensors repeatedly appear and disappear from the screen when the CAN main bus lines are normal (there is no open, short, short to +B or short to GND in the main bus lines), there may be a ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Front Door Belt Moulding: Installation
INSTALLATION CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY Install in this Direction (a) Engage the 8 claws as shown in the illustration to install ...