Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Visual Mute Signal Circuit between Radio Receiver and Multi-display

Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual / Audio & Visual & Telematics / Audio / Video / Audio And Visual System (for 12.3 Inch Display) / Visual Mute Signal Circuit between Radio Receiver and Multi-display

DESCRIPTION

The radio receiver assembly sends a visual mute signal to the multi-display assembly. As a result, a black screen is displayed when the screen changes so that noise and distorted images are not displayed.

When an open exists in the circuit, noise and distorted images will be displayed instead of a black screen.

When a short exists in the circuit, even though the multi-display assembly is operating normally, noise and distorted images will be displayed (black screen will not be displayed) during screen changes or the black screen will always be displayed.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click here

PROCEDURE

1.

INSPECT MULTI-DISPLAY ASSEMBLY

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

J56-11 (VMT1) - Body ground

Engine switch on (ACC), screen display changes

3.5 V or higher

→ Below 1 V

→ 3.5 V or higher

*a

Component with harness connected

(Multi-display Assembly)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.

CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY)

(a) Disconnect the J56 multi-display assembly connector.

(b) Disconnect the J151 radio receiver assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

J151-1 (VMTF) - J56-11 (VMT1)

Always

Below 1 Ω

J151-1 (VMTF) or J56-11 (VMT1) - Body ground

Always

10 kΩ or higher
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

3.

REPLACE MULTI-DISPLAY ASSEMBLY

(a) Replace the multi-display assembly with a new or known good one.

Click here

(b) Check that the screen display is normal.

OK:

Screen display is normal.

OK

END
NG

REPLACE RADIO RECEIVER ASSEMBLY

    Microphone Circuit
    DESCRIPTION The radio receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines. Using this circuit, the radio receive ...

    Radio Receiver Power Source Circuit
    DESCRIPTION This is the power source circuit to operate the radio receiver assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before perfor ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Can Communication System: Check Bus 3 Line for Short to GND
    DESCRIPTION There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminal 6 (CA3H) of the network gateway ECU and terminal 4 (CG) of the DLC3, or terminal 21 (CA3L) of the network gateway ECU and terminal 4 (CG) of the DLC3. Symptom Trouble A ...

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Smart Access System With Push-button Start (for Entry Function): Open in Front Passenger Side Electrical Antenna Circuit (B27A2)
    DESCRIPTION The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the front door outside handle assembly (for front passenger door) (electrical key antenna) at intervals of 0.25 seconds. For the front door outside handle assembly (for front passenger d ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2025 Copyright www.lexusrx.net
    0.0133