DESCRIPTION
The multiplex network master switch assembly sends the mirror adjust switch signals to the main body ECU (multiplex network body ECU) via LIN communication. The main body ECU (multiplex network body ECU) then sends the received mirror adjust switch signals to each outer mirror control ECU assembly via CAN communication. Based on this signal, each outer mirror control ECU assembly operates the vertical and horizontal mirror motors to adjust the mirror surface position.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Click here
Click here
PROCEDURE
| 1. | READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Master Switch / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Master Switch > Data List| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Mirror Selection SW (L) | Mirror select switch signal for LH mirror | OFF or ON | OFF: Mirror select switch off ON: Mirror select switch L switch on | - |
| Mirror Selection SW (R) | Mirror select switch signal for RH mirror | OFF or ON | OFF: Mirror select switch off ON: Mirror select switch R switch on | - |
| Mirror Position SW (L) | Mirror adjust switch signal (Left) | OFF or ON | OFF: Mirror adjust switch not pressed left ON: Mirror adjust switch pressed left | Check with the mirror select switch L or R switch on |
| Mirror Position SW (R) | Mirror adjust switch signal (Right) | OFF or ON | OFF: Mirror adjust switch not pressed right ON: Mirror adjust switch pressed right | Check with the mirror select switch L or R switch on |
| Mirror Position SW (Up) | Mirror adjust switch signal (Up) | OFF or ON | OFF: Mirror adjust switch not pressed up ON: Mirror adjust switch pressed up | Check with the mirror select switch L or R switch on |
| Mirror Position SW (Dwn) | Mirror adjust switch signal (Down) | OFF or ON | OFF: Mirror adjust switch not pressed down ON: Mirror adjust switch pressed down | Check with the mirror select switch L or R switch on |
| Tester Display |
|---|
| Mirror Selection SW (L) |
| Mirror Selection SW (R) |
| Mirror Position SW (L) |
| Mirror Position SW (R) |
| Mirror Position SW (Up) |
| Mirror Position SW (Dwn) |
OK:
On the Techstream screen, ON or OFF is displayed accordingly.
| NG | | REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
|
| 2. | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
(a) Temporarily replace the main body ECU (multiplex network body ECU) with a new or known good one.
Click here
|
| 3. | CHECK POWER MIRROR CONTROL OPERATION |
(a) Check the electrical remote control mirror function.
Click here
OK:
Electrical remote control mirror function operates normally.
| OK | | END (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) WAS DEFECTIVE) |
| NG | | REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch
Mirror Heater does not Operate with Rear Defogger SwitchLexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Power Steering System: Terminals Of Ecu
TERMINALS OF ECU CHECK POWER STEERING ECU ASSEMBLY *a Component without harness connected (Power Steering ECU Assembly) - - (a) Measure the voltage and resistance according to the value(s) in the table below. NOTICE: When the EPS warning light is illuminated due to a malfunction, the fa ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Blind Spot Monitor System: Master Module Horizontal Axis Misalignment (C1AC1)
DESCRIPTION This DTC is stored when the angle of the blind spot monitor sensor LH deviates more than the allowable range from the horizontal axis. HINT:
If a drum tester such as a speedometer tester, brake/speedometer combination tester or chassis dynamometer is used with the blind spot monitor s ...