REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during towing converter relay removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
|
*1: When performing learning using the Techstream.
Click here | |||
| Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane Control System | |
| Pre-collision System | |||
| Intelligent Clearance Sonar System*1 | |||
| Parking Assist Monitor System | | ||
| Panoramic View Monitor System | | ||
| Lighting System (w/ Automatic Headlight Beam Level Control System) | | ||
| Initialize back door lock | Power Door Lock Control System | | |
| Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) | | |
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
PROCEDURE
1. REMOVE TONNEAU COVER ASSEMBLY
Click here
2. REMOVE DECK BOARD ASSEMBLY
Click here
3. REMOVE REAR NO. 3 FLOOR BOARD
Click here
4. REMOVE REAR DECK FLOOR BOX
Click here
5. REMOVE REAR NO. 4 FLOOR BOARD
Click here
6. REMOVE DECK SIDE TRIM BOX RH
Click here
7. REMOVE REAR FLOOR FINISH PLATE
Click here
8. REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
Click here
9. REMOVE REAR SEAT ASSEMBLY RH
Click here
10. REMOVE UPPER QUARTER TRIM PAD RH
HINT:
Use the same procedure as for the LH side.
Click here
11. REMOVE REAR SEAT SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
Click here
12. REMOVE REAR FLOOR FINISH SIDE PLATE RH
HINT:
Use the same procedure as for the LH side.
Click here
13. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
Click here
14. REMOVE ROPE HOOK ASSEMBLY
HINT:
Use the same procedure as for the LH side.
Click here
15. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
Click here
16. REMOVE RECLINING REMOTE CONTROL BEZEL RH (w/o Rear Power Seat System)
Click here
17. REMOVE FOLD SEAT SWITCH ASSEMBLY (w/ Rear Power Seat System)
Click here
18. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH
Click here
19. REMOVE TOWING CONVERTER RELAY
(a) Disconnect the connector.
| (b) Remove the bolt. |
|
(c) Disengage the guide to remove the towing converter relay.
On-vehicle Inspection
InstallationLexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Quarter Trim Speaker (w/o Rear No. 2 Seat): Inspection
INSPECTION PROCEDURE 1. INSPECT QUARTER SIDE SPEAKER ASSEMBLY (a) With the speaker installed, check that there is no looseness or other abnormalities. (b) Check that there is no foreign matter in the speaker, no tears on the speaker cone or other abnormalities. (c) Measure the resistance of the s ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Intelligent Clearance Sonar System: Steering Angle Sensor Failure (C1626)
DESCRIPTION This DTC is stored if the clearance warning ECU assembly receives a signal via CAN communication from the steering sensor that indicates an internal malfunction. DTC No. Detection Item DTC Detection Condition Trouble Area C1626 Steering Angle Sensor Failure A fail flag i ...