Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT

HINT:

  • Use the following procedure to troubleshoot the front power seat control system (w/ Memory).
  • *: Use the Techstream.

PROCEDURE

1.

VEHICLE BROUGHT TO WORKSHOP

NEXT

2.

CUSTOMER PROBLEM ANALYSIS

(a) Interview the customer to confirm the problem.

Click here

NEXT

3.

PRE-CHECK

(a) Measure the battery voltage.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.

(b) Check the fuses and relays.

(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.

NEXT

4.

INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

(a) Using the Techstream, check for CAN communication system DTCs.

Click here

Result

Proceed to

CAN DTCs are not output

A

CAN DTCs are output

B

B

GO TO CAN COMMUNICATION SYSTEM

A

5.

INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*

(a) Using the Techstream, check for LIN communication system DTCs.

Click here

Result

Proceed to

LIN DTCs are not output

A

LIN DTCs are output

B

B

GO TO LIN COMMUNICATION SYSTEM

A

6.

CHECK FOR DTC*

(a) Clear the DTCs.

Click here

Body Electrical > Driver Seat > Clear DTCs

(b) Recheck for DTCs.

Click here

Body Electrical > Driver Seat > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTCs are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A

7.

PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in problem symptoms table

A

Fault is listed in problem symptoms table

B

B

GO TO STEP 9

A

8.

OVERALL ANALYSIS AND TROUBLESHOOTING*

(a) Operation Check

Click here

(b) Data List / Active Test

Click here

(c) Terminals of ECU

Click here

(d) Inspection

NEXT

9.

REPAIR OR REPLACE

NEXT

10.

CONFIRMATION TEST

NEXT

END

    System Diagram
    SYSTEM DIAGRAM Communication Table Sender Receiver Signal Line ECM Main Body ECU (Multiplex Network Body ECU) Transmission information Shift position P signal CAN Ou ...

    Operation Check
    OPERATION CHECK CHECK POWER SEAT FUNCTION (a) Check the basic functions. *a Slide Function *b Reclining Function *c Lifter Function *d Front Vertical Function *e Lumbar S ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Heated Steering Wheel Controller: Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the steering vibration and heater ECU removal/installation are shown below. Necessary Procedure After Part ...

    Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Panoramic View Monitor System: Initialization
    INITIALIZATION INITIALIZE PANORAMIC VIEW MONITOR SYSTEM (a) When "!" is displayed on the multi-display assembly, correct the steering angle neutral point using the following method. (1) Fully turn the steering wheel to the left and right on level ground. NOTICE: Memorizing the steering angle neutral ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2026 Copyright www.lexusrx.net
    0.0091