REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat cushion heater removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced| Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here | |||
| Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane Control System | |
| Pre-collision System | |||
| Intelligent Clearance Sonar System* | |||
| Parking Assist Monitor System | | ||
| Panoramic View Monitor System | | ||
| Lighting System (w/ Automatic Headlight Beam Level Control System) | | ||
| Initialize back door lock | Power Door Lock Control System | | |
| Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) | | |
| Initialize position control ECU | Front Power Seat Control System (w/ Memory) | |
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
HINT:
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY
Click here
2. DISCONNECT FRONT SEATBACK BOARD SUB-ASSEMBLY
Click here
3. REMOVE FRONT SEAT CUSHION SHIELD (for Standard Seat Type)
Click here
4. REMOVE INNER NO. 1 FRONT SEAT CUSHION SHIELD (for Standard Seat Type)
Click here
5. REMOVE INNER NO. 1 FRONT SEAT CUSHION SHIELD (for Sports Seat Type)
Click here
6. REMOVE FRONT SEAT CUSHION SHIELD (for Sports Seat Type)
Click here
7. REMOVE FRONT SEAT INNER CUSHION SHIELD
Click here
8. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Click here
9. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD (for Standard Seat Type)
| (a) Disconnect the 2 connectors. |
|
(b) Disengage the 4 clamps.
(c) w/o Variable Seat Cushion System:
(1) Disengage the 10 hooks to remove the separate type front seat cushion cover with pad.
(d) w/ Variable Seat Cushion System:
(1) Disengage the 2 fasteners.
| Fastener |
| (2) Disengage the 4 hooks. |
|
| (3) Remove the 4 hog rings. |
|
(4) Disengage the 7 hooks to remove the separate type front seat cushion cover with pad.
10. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER (for Standard Seat Type)
| (a) w/o Variable Seat Cushion System: (1) Remove the 6 hog rings. |
|
| (b) w/ Variable Seat Cushion System: (1) Remove the 2 hog rings. |
|
| (c) Remove the 18 hog rings and separate type front seat cushion cover from the separate type front seat cushion pad. |
|
11. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY (for Standard Seat Type)
| (a) Remove the 44 tag pins and front seat cushion heater assembly from the separate type front seat cushion cover. |
|
12. REMOVE FRONT SEAT CUSHION HEATER (FRONT SEAT CUSHION PAD WITH COVER) (for Sports Seat Type)
HINT:
The front seat cushion heater cannot be removed from the front seat cushion pad with cover as they are a unit.
| (a) Disconnect the 2 connectors. |
|
(b) Disengage the 4 clamps.
(c) Disengage the 10 hooks to remove the front seat cushion heater (front seat cushion pad with cover).
.png)
InstallationLexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Lighting System (w/ Automatic Headlight Beam Level Control System): Dtc Check / Clear
DTC CHECK / CLEAR CHECK FOR DTC (MAIN BODY) (a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Main Body / Trouble Codes. Body Electrical > Main Body > Trouble Codes (e) Check for DTCs. CHECK ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Transmission Control Cable: Adjustment
ADJUSTMENT CAUTION / NOTICE / HINT NOTICE: Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and the shift lever are in neutral. PROCEDURE 1. SECURE VEHICLE (a) Fully apply the parking brake and chock a wheel. CAUTION:
Make sure to app ...