REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seatback heater removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced| Replaced Part or Performed Procedure | Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| Disconnect cable from negative battery terminal | Memorize steering angle neutral point | Lane Control System | |
| Pre-collision System | |||
| Intelligent Clearance Sonar System*1 | |||
| Parking Assist Monitor System | | ||
| Panoramic View Monitor System | | ||
| Lighting System (w/ Automatic Headlight Beam Level Control System) | | ||
| Initialize back door lock | Power Door Lock Control System | | |
| Reset back door close position | Power Back Door System (w/ Outside Door Control Switch) | |
*1: When performing learning using the Techstream.
Click here
CAUTION:
Click here
PROCEDURE
1. REMOVE REAR SEAT ASSEMBLY LH (w/o Rear No. 2 Seat)
Click here
2. REMOVE REAR CENTER SEAT INNER BELT ASSEMBLY (w/o Rear No. 2 Seat)
Click here
3. REMOVE REAR SEAT COVER CAP LH (w/o Rear No. 2 Seat)
for Manual Seat:
Click here
4. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH (w/o Rear No. 2 Seat)
for Manual Seat:
Click here
5. REMOVE POWER SEAT SWITCH ASSEMBLY (w/o Rear No. 2 Seat)
for Power Seat:
Click here
6. DISCONNECT SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD (w/o Rear No. 2 Seat)
Click here
7. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD (w/o Rear No. 2 Seat)
Click here
8. REMOVE REAR SEATBACK COVER LH (w/o Rear No. 2 Seat)
Click here
9. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH (w/o Rear No. 2 Seat)
Click here
10. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD (w/o Rear No. 2 Seat)
Click here
11. REMOVE SEPARATE TYPE REAR SEATBACK COVER (w/o Rear No. 2 Seat)
Click here
12. REMOVE SEAT HEATER ASSEMBLY (w/o Rear No. 2 Seat)
| (a) Remove the 10 tag pins and seat heater assembly from the separate type rear seatback cover. |
|
13. REMOVE REAR NO. 1 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat)
Click here
14. REMOVE REAR SEAT COVER CAP LH (w/ Rear No. 2 Seat)
Click here
15. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH (w/ Rear No. 2 Seat)
Click here
16. REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat)
Click here
17. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD (w/ Rear No. 2 Seat)
Click here
18. REMOVE REAR SEATBACK COVER LH (w/ Rear No. 2 Seat)
Click here
19. REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY LH (w/ Rear No. 2 Seat)
Click here
20. REMOVE REAR SEAT UPPER RECLINING COVER LH (w/ Rear No. 2 Seat)
Click here
21. REMOVE RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat)
Click here
22. REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD (w/ Rear No. 2 Seat)
Click here
23. REMOVE SEPARATE TYPE REAR SEATBACK COVER (w/ Rear No. 2 Seat)
Click here
24. REMOVE SEAT HEATER ASSEMBLY (w/ Rear No. 2 Seat)
| (a) Remove the 10 tag pins and seat heater assembly from the separate type rear seatback cover. |
|
Inspection
InstallationLexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Fuel Lid Opener Unit: Removal
REMOVAL PROCEDURE 1. PRECAUTION Click here 2. REMOVE FUEL LID LOCK WITH MOTOR ASSEMBLY Click here 3. REMOVE REAR WHEEL LH Click here 4. REMOVE REAR WHEEL HOUSE LINER LH (a) Remove the screw. (b) Remove the 2 screws. (c) Remove the 2 grommets. HINT: The grom ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Rear Power Seat Control System(for Second Row): Folding Motor Circuit
DESCRIPTION HINT:
The rear power seat switch is a collective term for the rear power seat switch RH and the rear power seat switch LH.
The rear seatback frame sub-assembly is a collective term for the rear seatback frame sub-assembly RH and the rear seatback frame sub-assembly LH.
The fold s ...