Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual: Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat heater switch removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedures

Effect/Inoperative Function When Necessary Procedures are not Performed

Link

Disconnect cable from negative battery terminal

Memorize steering angle neutral point

Lane Control System

Pre-collision System

Intelligent Clearance Sonar System*1

Parking Assist Monitor System

Panoramic View Monitor System

Lighting System (w/ Automatic Headlight Beam Level Control System)

Initialize back door lock

Power Door Lock Control System

Reset back door close position

Power Back Door System (w/ Outside Door Control Switch)

*1: When performing learning using the Techstream.

Click here

CAUTION:

  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

PROCEDURE

1. REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY (for Console Box)

Click here

2. REMOVE REFRESHING SEAT SWITCH (for Console Box)

(a) Remove the 3 screws.

(b) Disengage the 2 guides to remove the refreshing seat switch.

3. REMOVE REAR NO. 1 SEAT ASSEMBLY RH (for Armrest)

for 60/40 Split Seat Type RH Side:

Click here

4. REMOVE REAR SEATBACK COVER (for Armrest)

Click here

5. REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY (for Armrest)

(a) Disengage the 2 hooks.

(b) Disengage the 4 hooks.

(c) Disengage the 10 claws and 5 clips to remove the rear seatback board sub-assembly as shown in the illustration.

Place Hand Here

Remove in this Direction

6. REMOVE CENTER ARMREST HINGE COVER LH (for Armrest)

Click here

7. REMOVE NO. 1 SEAT ARMREST ASSEMBLY (for Armrest)

Click here

8. REMOVE ARMREST ASSEMBLY (for Armrest)

Click here

9. REMOVE CENTER ARMREST HINGE COVER RH (for Armrest)

Click here

10. REMOVE REAR SEAT CENTER ARMREST ASSEMBLY (for Armrest)

Click here

11. REMOVE REAR SEAT CENTER ARMREST COVER (for Armrest)

Click here

12. REMOVE CUP HOLDER ASSEMBLY (for Armrest)

Click here

13. REMOVE REAR SEAT CENTER ARMREST DOOR SUB-ASSEMBLY (for Armrest)

Click here

14. REMOVE NO. 2 REAR SEAT CENTER ARMREST BOX (for Armrest)

Click here

15. REMOVE REAR SEAT HEATER SWITCH (for Armrest)

(a) Disconnect the connector.

(b) Remove the 3 screws and rear seat heater switch.

    Inspection
    INSPECTION PROCEDURE 1. INSPECT REFRESHING SEAT SWITCH (for Rear Side) (a) Apply battery voltage and check the operation of the switch according to the table below. OK: Battery Connection Con ...

    Installation
    INSTALLATION CAUTION / NOTICE / HINT CAUTION: Wear protective gloves. Sharp areas on the seat frame may injure your hands. PROCEDURE 1. INSTALL REFRESHING SEAT SWITCH (for Console Box) (a) Engage the ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Steering Heater Switch: Removal
    REMOVAL PROCEDURE 1. REMOVE INSTRUMENT PANEL GARNISH LH Click here 2. REMOVE FRONT DOOR SCUFF PLATE LH w/ Rear No. 2 Seat: Click here w/o Rear No. 2 Seat: Click here 3. REMOVE COWL SIDE TRIM BOARD LH Click here 4. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Click here 5. DI ...

    Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Trip Switch: Removal
    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during trip switch removal/installation are shown below. Necessary Procedures After Parts Removed/Installed/Rep ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2024 Copyright www.lexusrx.net
    0.0147