INSTALLATION
PROCEDURE
1. INSTALL THEFT WARNING SIREN ASSEMBLY
(a) Connect the connector.
(b) Engage the 2 guides to install the theft warning siren assembly with the 2 bolts.
(c) Engage the clamp.
2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (w/o Rear No. 2 Seat)
Click here
3. INSTALL RECLINING REMOTE CONTROL BEZEL RH (w/o Rear No. 2 Seat)
w/o Rear Power Seat System:
Click here
4. INSTALL FOLD SEAT SWITCH ASSEMBLY (w/o Rear No. 2 Seat)
w/ Rear Power Seat System:
Click here
5. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/o Rear No. 2 Seat)
Click here
6. INSTALL ROPE HOOK ASSEMBLY (w/o Rear No. 2 Seat)
HINT:
Use the same procedure as for the LH side.
Click here
7. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (w/o Rear No. 2 Seat)
Click here
8. INSTALL REAR FLOOR FINISH SIDE PLATE RH (w/o Rear No. 2 Seat)
HINT:
Use the same procedure as for the LH side.
Click here
9. INSTALL REAR SEAT SIDE GARNISH RH (w/o Rear No. 2 Seat)
HINT:
Use the same procedure as for the LH side.
Click here
10. INSTALL UPPER QUARTER TRIM PAD RH (w/o Rear No. 2 Seat)
HINT:
Use the same procedure as for the LH side.
Click here
11. INSTALL REAR SEAT ASSEMBLY RH (w/o Rear No. 2 Seat)
Click here
12. INSTALL REAR DOOR SCUFF PLATE RH (w/o Rear No. 2 Seat)
HINT:
Use the same procedure as for the LH side.
Click here
13. INSTALL REAR FLOOR FINISH PLATE (w/o Rear No. 2 Seat)
Click here
14. INSTALL DECK SIDE TRIM BOX RH (w/o Rear No. 2 Seat)
Click here
15. INSTALL REAR NO. 4 FLOOR BOARD (w/o Rear No. 2 Seat)
Click here
16. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)
Click here
17. INSTALL REAR NO. 3 FLOOR BOARD (w/o Rear No. 2 Seat)
Click here
18. INSTALL DECK BOARD ASSEMBLY (w/o Rear No. 2 Seat)
Click here
19. INSTALL TONNEAU COVER ASSEMBLY (w/o Rear No. 2 Seat)
Click here
20. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (w/ Rear No. 2 Seat)
Click here
21. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/ Rear No. 2 Seat)
Click here
22. INSTALL ROPE HOOK ASSEMBLY (w/ Rear No. 2 Seat)
HINT:
Use the same procedure as for the LH side.
Click here
23. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (w/ Rear No. 2 Seat)
Click here
24. INSTALL REAR SEAT SIDE GARNISH RH (w/ Rear No. 2 Seat)
Click here
25. INSTALL FRONT DECK SIDE TRIM COVER RH (w/ Rear No. 2 Seat)
HINT:
Use the same procedure as for the LH side.
Click here
26. INSTALL REAR SEAT OUTER TRACK BRACKET COVER RH (w/ Rear No. 2 Seat)
for 60/40 Split Seat Type:
Click here
for Captain Seat Type:
HINT:
Use the same procedure as for the LH side.
Click here
27. INSTALL REAR DOOR INSIDE SCUFF PLATE RH (w/ Rear No. 2 Seat)
HINT:
Use the same procedure as for the LH side.
Click here
28. INSTALL REAR DOOR SCUFF PLATE RH (w/ Rear No. 2 Seat)
HINT:
Use the same procedure as for the LH side.
Click here
29. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
Click here
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Air Conditioning Pressure Sensor: On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT AIR CONDITIONER PRESSURE SENSOR (a) Check the wire harness. (1) Disconnect the A9 air conditioner pressure sensor connector. (2) Disconnect the J42 air conditioning amplifier assembly connector. (3) Measure the resistance according to the value(s) in the ta ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Vehicle Stability Control System: Multi-axis Acceleration Sensor Module "A" Supply Voltage Circuit Voltage Out of Range (C14D71C)
DESCRIPTION for TFT Meter Type:
The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition.
This DTC is stored when the skid control ECU (brake actuator assembly) receives a sensor supply voltage malfunction signal from the acceleration sensor (ai ...