Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Open in Outer Mirror Indicator(Slave) (C1AB5)
DESCRIPTION
This DTC is stored when the blind spot monitor sensor RH detects an open in the outer rear view mirror indicator RH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AB5 | Open in Outer Mirror Indicator(Slave) | Both of the following conditions are met:
|
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
When checking for DTCs, make sure that the blind spot monitor system is turned on.
PROCEDURE
| 1. | CHECK DTC |
(a) Turn the engine switch off.
(b) Turn the engine switch on (IG).
(c) Recheck for DTCs and check if the same DTC is output again.
Body Electrical > Blind Spot Monitor Slave > Trouble CodesOK:
No DTCs are output.
| OK | .gif) | USE SIMULATION METHOD TO CHECK |
|
.gif)
| 2. | CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - BLIND SPOT MONITOR SENSOR RH AND BODY GROUND) |
(a) Disconnect the W2 blind spot monitor sensor RH connector.
(b) Disconnect the M4 outer mirror control ECU assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| W2-4 (OMIR) - M4-13 (BDSR) | Always | Below 1 Ω |
| M4-7 (GND) - Body ground | Always | Below 1 Ω |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 3. | INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH |
(a) Disconnect the z13 outer rear view mirror assembly RH connector.
| (b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | | REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH |
|
| 4. | INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH |
(a) Disconnect the IND2 outer mirror RH connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z13-8 (BSM+) - IND2-3 (+) | Always | Below 1 Ω |
| z13-12 (TRN-) - IND2-2 (-) | Always | Below 1 Ω |
| NG | | REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH |
|
| 5. | INSPECT OUTER MIRROR RH |
(a) Remove the outer mirror RH.
Click here .gif)
(b) Inspect the outer rear view mirror indicator RH on the outer mirror RH.
Click here
| OK | | REPLACE BLIND SPOT MONITOR SENSOR RH |
| NG | | REPLACE OUTER MIRROR RH |
Open in Outer Mirror Indicator(Master) (C1AB4)
DESCRIPTION This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH. DTC No. Detection Item DTC Detection Condition Trouble Area ...
Blind Spot Monitor Master Module (C1AB6)
DESCRIPTION This DTC is stored when the blind spot monitor sensor LH detects an internal malfunction. DTC No. Detection Item DTC Detection Condition Trouble Area C1AB6 Blind Spot Monito ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Driving Support Buzzer: Installation
INSTALLATION PROCEDURE 1. INSTALL SKID CONTROL BUZZER ASSEMBLY (a) Connect the connector. HINT: Make sure to install the skid control buzzer assembly in the correct direction. (b) Engage the clamp to install the skid control buzzer assembly. NOTICE: If the skid control buzzer assembly ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Park / Neutral Position Switch: Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during park/neutral position switch assembly removal/installation are shown below. Necessary Procedures After P ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0091