Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual: Brake System (C1A50)
DESCRIPTION
When a vehicle stability control system malfunction signal sent from the skid control ECU assembly is detected by the clearance warning ECU assembly, DTC C1A50 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A50 | Brake System | When the engine switch is on (IG), a VSC warning light malfunction signal is detected for 1 second or more. |
|
CAUTION / NOTICE / HINT
NOTICE:
-
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
.gif)
-
After replacing an ultrasonic sensor or the clearance warning ECU assembly, perform the necessary procedures (adjustment, calibration, initialization or registration).
Click here
PROCEDURE
| 1. | CHECK DTC OUTPUT |
(a) Using the Techstream, check for DTCs according to the prompts on the screen.
Click here
HINT:
After turning the engine switch from off to on (IG), wait 4 seconds or more before checking for DTCs.
Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Trouble Codes(b) Clear the DTCs according to the screen on the Techstream.
Click here
(c) Recheck for DTCs.
Click here
HINT:
- DTC C1A50 is stored when a malfunction signal sent from the vehicle stability control system is detected.
- If the malfunctioning part has been repaired or replaced before rechecking for DTCs, DTC C1A50 will not be output again.
-
If DTC C1A50 is output frequently, duplicate the conditions that cause the problem symptoms and perform the inspection again, even though the DTC was not output when rechecking for DTCs.
Click here
| Result | Proceed to |
|---|---|
| DTC C1A50 is output | A |
| DTC C1A50 is not output | B |
| A | .gif) | GO TO VEHICLE STABILITY CONTROL SYSTEM |
| B | | USE SIMULATION METHOD TO CHECK |
Stop Light Relay Circuit (C1A4B)
DESCRIPTION When a stop light relay circuit malfunction signal sent from the vehicle stability control system is detected by the clearance warning ECU assembly, DTC C1A4B is stored. DTC No. Detec ...
Steering Angle Midpoint Initial Setting Incomplete (C1AEA)
DESCRIPTION When the clearance warning ECU assembly detects that the steering angle neutral point memorization is incomplete during self diagnosis, C1AEA is stored. DTC No. Detection Item DTC D ...
Other materials:
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Audio And Visual System (for 12.3 Inch Display): Operation Check
OPERATION CHECK REMOTE TOUCH (REMOTE OPERATION CONTROLLER ASSEMBLY) SELF CHECK NOTICE:
Before entering self-diagnostic mode, make sure there are no obstructions which may interfere with operation of the remote touch screen, and that the remote touch screen is not dirty.
Do not touch the remote ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Fuel Pump (for Tmmc Made): Inspection
INSPECTION PROCEDURE 1. INSPECT FUEL PUMP (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Specified Condition U - V 0.05 to 3.0 Ω V - W 0.05 to 3.0 Ω U - W 0.05 to 3.0 Ω If the result is not as specified ...
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual
- For your information
- Pictorial index
- For safety and security
- Instrument cluster
- Operation of each component
- Driving
- Lexus Display Audio system
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- For owners
Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual
0.0099