CUSTOMIZE PARAMETERS
CUSTOMIZE INTUITIVE PARKING ASSIST SYSTEM
(a) Customizing with the Techstream.
NOTICE:
(1) Connect the Techstream to the DLC3.
(2) Turn the engine switch on (IG).
(3) Turn the intuitive parking assist system on.
(4) Turn the Techstream on.
(5) Enter the following menus: Body Electrical / Advanced Parking Guidance/ICS/Intuitive P/A / Utility / Customize Setting.
(6) Select the setting by referring to the table below.
Warning| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Fr Corner Sensor Onset Range | Sets the detection operation range for the front corner sensors. | Long | 0:Short,1:Long | Clearance warning ECU assembly |
| Rr Corner Sensor Onset Range | Sets the detection operation range for the rear corner sensors. | Long | 0:Short,1:Long | Clearance warning ECU assembly |
| Fr Sensor Onset Range | Sets the detection operation range for the front center sensors. | Wide | 0:Narrow,1:Wide | Clearance warning ECU assembly |
| Rr Sensor Onset Range | Sets the detection operation range for the rear center sensors. | Wide | 0:Narrow,1:Wide | Clearance warning ECU assembly |
| Fr & Rr Buzzer Volume | Changes the buzzer volume setting. | M | 01:L,10:M,11:H | Clearance warning ECU assembly |
| Intuitive P/A Auto Mute Function | Sets the availability of the auto mute function. | ON | 0:ON,1:OFF | Clearance warning ECU assembly |
| Intuitive P/A Judgement of Obstacle on Course | Sets the availability of judgement of obstacle on course. | Valid | 0:Valid,1:Invalid | Clearance warning ECU assembly |
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Sensor Condition N | Makes the front sensors available when the shift lever is in N. | Avail | 0:Not Avail,1:Avail | Clearance warning ECU assembly |
| Tester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Approach Display OFF | Sets whether the display turns off after an obstacle is no longer detected. | Avail | 0:Not Avail,1:Avail | Clearance warning ECU assembly |
| Display Mode | The display mode setting (when the intuitive parking assist system is normal). | All | 01:All,11:Undisp | Clearance warning ECU assembly |
(b) Customizing with multi-information display
NOTICE:
(1) Turn the engine switch on (IG).
(2) Turn the intuitive parking assist system on.
(3) Enter the following menus.
(4) Select the setting by referring to the table below.
PKSA (Parking support alert)| Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Buzzer volume | Sets the buzzer alert volume. | 2 | 1, 2 or 3 | Clearance warning ECU assembly |
| Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
| Intuitive parking assist | Sets the Intuitive parking assist system. | On | On/Off | Clearance warning ECU assembly |
Operation Check
CalibrationLexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Rear Airbag Sensor(w/o Rear No. 2 Seat): Removal
REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the rear airbag sensor removal/installation are shown below. Necessary Procedure After Parts Removed/Insta ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Can Communication System: Check Bus 3 Lines for Short Circuit
DESCRIPTION There may be a short circuit between the bus 3 main lines and/or bus 3 branch lines when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the network gateway ECU is below 54 Ω. Symptom Trouble Area Resistance between terminals 6 (CA3H) and 21 (CA3L) of network gateway ...