CAUTION / NOTICE / HINT
HINT:
PROCEDURE
1. | VEHICLE BROUGHT TO WORKSHOP |
|
2. | CUSTOMER PROBLEM ANALYSIS |
(a) Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.
HINT:
The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.
Problem Symptom | Cause |
---|---|
The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced. | The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver. |
|
3. | INSPECT BATTERY VOLTAGE |
(a) Measure the battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, replace or recharge the battery before proceeding.
|
4. | SYSTEM CHECK |
(a) Check the vehicle specification.
Result | Proceed to |
---|---|
w/ Navigation System | A |
w/ Audio and Visual System | B |
B | ![]() | GO TO STEP 6 |
|
5. | CHECK NAVIGATION SYSTEM |
(a) Refer to Navigation System.
Click here
OK:
Navigation system is normal.
OK | ![]() | GO TO STEP 7 |
NG | ![]() | GO TO NAVIGATION SYSTEM |
6. | CHECK AUDIO AND VISUAL SYSTEM |
(a) Refer to the Audio and Visual System.
for 12.3 Inch Display: Click here
for 8 Inch Display: Click here
OK:
Audio and visual system is normal.
NG | ![]() | GO TO AUDIO AND VISUAL SYSTEM |
|
7. | CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Use the Techstream to check if the CAN communication system is functioning normally.
Click here
Result | Proceed to |
---|---|
CAN DTCs are not output | A |
CAN DTCs are output | B |
B | ![]() | GO TO CAN COMMUNICATION SYSTEM |
|
8. | CHECK FOR DTC* |
(a) Check for DTCs and note any codes that are output.
Chassis > Circumference Monitoring Camera Control Module > Trouble Codes(b) Clear the DTCs.
Chassis > Circumference Monitoring Camera Control Module > Clear DTCs(c) Recheck for DTCs. Try to reproduce the DTC by simulating the original activity that the DTC suggests.
Chassis > Circumference Monitoring Camera Control Module > Trouble Codes Result | Proceed to |
---|---|
DTCs are not output | A |
DTCs are output | B |
B | ![]() | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
9. | PROBLEM SYMPTOMS TABLE |
(a) Refer to the Problem Symptoms Table.
Click here
Result | Proceed to |
---|---|
Fault is not listed in Problem Symptoms Table | A |
Fault is listed in Problem Symptoms Table | B |
B | ![]() | GO TO STEP 11 |
|
10. | OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Data List / Active Test
Click here
(b) Terminals of ECU
Click here
|
11. | ADJUST, REPAIR OR REPLACE |
|
12. | CONFIRMATION TEST |
NEXT | ![]() | END |
Lexus RX (RX 350L, RX450h) 2016-2023 Repair Manual > Vehicle Stability Control System: Left Front Wheel Speed Sensor Signal Stuck Low (C050023)
DESCRIPTION Refer to DTC C05001F. Click here DTC No. Detection Item DTC Detection Condition Trouble Area C050023 Left Front Wheel Speed Sensor Signal Stuck Low Any of the following is detected:
When the +BS terminal voltage is 17.4 V or less at a vehicle speed of 10 km/h (6 mph ...
Lexus RX (RX 350L, RX450h) 2016-2023 Repair Manual > Rear Crankshaft Oil Seal: Installation
INSTALLATION PROCEDURE 1. INSTALL REAR ENGINE OIL SEAL (a) Apply MP grease to the lip of a new rear engine oil seal. *1 Rear Engine Oil Seal Retainer *a Oil Seal Protrusion Height (b) Using SST and a hammer, tap in the rear engine oil seal. SST: 09223-15030 SST: 0995 ...