DESCRIPTION
The multi-display assembly and radio receiver assembly are connected by AVC-LAN communication lines.
This DTC is stored when an AVC-LAN communication error occurs between the multi-display assembly and radio receiver assembly.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
---|---|---|---|
B15D6 | Display Disconnected | A device that is listed in the AVC-LAN connected device record of the master unit is missing |
|
HINT:
The radio receiver assembly is the master unit.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Click here
PROCEDURE
1. | CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING) |
(a) Check for optional components.
(1) Check that optional components (including associated wiring) which generate radio waves are not installed.
Result | Proceed to |
---|---|
Optional components (including associated wiring) are installed. | A |
Optional components (including associated wiring) are not installed. | B |
HINT:
B | ![]() | GO TO STEP 3 |
|
2. | REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING) |
(a) Remove optional components (including associated wiring).
NOTICE:
Do not remove optional components or associated wiring without the permission of the customer.
|
3. | CHECK DTC |
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
OK | ![]() | END |
|
4. | CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY POWER SOURCE) |
(a) Disconnect the J56 multi-display assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
---|---|---|
J56-13 (GND1) - Body ground | Always | Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
---|---|---|
J56-12 (B) - J56-13 (GND1) | Always | 11 to 14 V |
J56-24 (ACC) - J56-13 (GND1) | Engine switch on (ACC) | 11 to 14 V |
NG | ![]() | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
5. | CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - MULTI-DISPLAY ASSEMBLY) |
(a) Disconnect the J148 radio receiver assembly connector.
(b) Disconnect the J56 multi-display assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
---|---|---|
J148-5 (TX1+) - J56-7 (TX+) | Always | Below 1 Ω |
J148-6 (TX1-) - J56-19 (TX-) | Always | Below 1 Ω |
J148-5 (TX1+) or J56-7 (TX+) - Body ground | Always | 10 kΩ or higher |
J148-6 (TX1-) or J56-19 (TX-) - Body ground | Always | 10 kΩ or higher |
NG | ![]() | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
6. | REPLACE MULTI-DISPLAY ASSEMBLY |
(a) Replace the multi-display assembly with a new or known good one.
Click here
(b) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(c) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
OK | ![]() | END |
NG | ![]() | REPLACE RADIO RECEIVER ASSEMBLY |
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Generator (for 180 A Type): Reassembly
REASSEMBLY PROCEDURE 1. INSTALL GENERATOR DRIVE END FRAME BEARING (a) Using SST and a press, install a new generator drive end frame bearing to the generator drive end frame. SST: 09950-60010 09951-00470 SST: 09950-70010 09951-07100 (b) Fit the tabs of the retainer plate into the c ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Sfi System: Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground (P036511,P036515,P03652A,P036531,P039011,P039015,P039031)
DESCRIPTION The VVT sensor (for exhaust camshaft) (EV1, EV2 signal) consists of a magnet and MRE (Magneto Resistance Element). The exhaust camshaft has a timing rotor for the VVT sensor. When the exhaust camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects ...