CAUTION / NOTICE / HINT
NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here
PROCEDURE
1. | CHECK RADIO RECEIVER ASSEMBLY |
(a) Check the radio automatic station search function.
(1) Check the radio automatic station search function by activating it.
Result | Proceed to |
---|---|
Automatic station search function does not stop. | A |
Automatic station search function stops on a station. | B |
B | REPLACE RADIO RECEIVER ASSEMBLY |
|
2. | CHECK OPTIONAL COMPONENTS |
(a) Check if any optional components that may decrease reception capacity, such as a sunshade film or a telephone antenna, are installed.
Result | Proceed to |
---|---|
Optional components are not installed. | A |
Optional components are installed. | B |
NOTICE:
Do not remove optional components without the permission of the customer.
B | REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE) |
|
3. | CHECK RADIO RECEIVER ASSEMBLY |
(a) Preparation for check (1) Disconnect the antenna connector from the radio receiver assembly. | |
(b) Check for noise
(1) Turn the engine switch on (ACC) with the radio receiver assembly connector connected.
(2) Turn the radio on and tune into AM mode.
(3) Place a screwdriver, thin wire or other metal object on the radio receiver assembly antenna jack and check that noise can be heard from the speakers.
OK:
Noise can be heard from the speakers.
NG | REPLACE RADIO RECEIVER ASSEMBLY |
|
4. | INSPECT RADIO RECEIVER ASSEMBLY |
(a) Disconnect the RA radio receiver assembly connector.
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
NG | REPLACE RADIO RECEIVER ASSEMBLY |
|
5. | REPLACE ANTENNA CORD SUB-ASSEMBLY |
(a) Replace the antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally.
w/ Rear No. 2 Seat: Click here
w/o Rear No. 2 Seat: Click here
OK:
Radio broadcasts can be received normally.
OK | END |
|
6. | REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY |
(a) Replace the No. 2 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally.
w/ Rear No. 2 Seat: Click here
w/o Rear No. 2 Seat: Click here
OK:
Radio broadcasts can be received normally.
Result | Proceed to |
---|---|
OK (w/o Rear No. 2 Seat) | A |
OK (w/ Rear No. 2 Seat) | B |
NG | C |
B | GO TO STEP 9 |
C | END |
|
7. | REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY |
(a) Replace the No. 3 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally.
Click here
OK:
Radio broadcasts can be received normally.
OK | END |
|
8. | REPLACE REAR SPOILER SUB-ASSEMBLY |
(a) Replace the rear spoiler sub-assembly with a new or known good one and check if radio broadcasts can be received normally.
Click here
OK:
Radio broadcasts can be received normally.
OK | END |
NG | REPLACE RADIO RECEIVER ASSEMBLY |
9. | REPLACE NO. 5 ANTENNA CORD SUB-ASSEMBLY |
(a) Replace the No. 5 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally.
Click here
OK:
Radio broadcasts can be received normally.
OK | END |
|
10. | REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY |
(a) Replace the No. 3 antenna cord sub-assembly with a new or known good one and check if radio broadcasts can be received normally.
Click here
OK:
Radio broadcasts can be received normally.
OK | END |
|
11. | REPLACE REAR SPOILER SUB-ASSEMBLY |
(a) Replace the rear spoiler sub-assembly with a new or known good one and check if radio broadcasts can be received normally.
Click here
OK:
Radio broadcasts can be received normally.
OK | END |
NG | REPLACE RADIO RECEIVER ASSEMBLY |
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Front Bumper: Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE FRONT BUMPER ARM HOLE COVER LH (for Type A) (a) Remove the screw and clip. Screw Clip (b) Disengage the 3 guides to remove the front bumper arm hole cover LH. 2. REMOVE FRONT BUMPER ARM HOLE COVER LH (for Type B) (a) Remove the screw an ...
Lexus RX (RX 350L, RX450h) 2016-2024 Repair Manual > Automatic Transaxle System: Transmission Fluid Temperature Sensor "A" Circuit Short To Ground (P071011)
DESCRIPTION The ATF temperature sensor converts the automatic transaxle fluid (ATF) temperature into a resistance value for use by the ECM. The ECM applies voltage to the temperature sensor through terminal THO1 of the ECM. The sensor resistance changes with the ATF temperature. As the temperature r ...