DESCRIPTION
The combination meter assembly controls the illumination and turning off of the rear turn signal lights.
WIRING DIAGRAM
PROCEDURE
| 1. | CHECK OPERATION (REAR TURN SIGNAL LIGHTS) |
(a) Check the operation of the rear turn signal lights.
| Result | Proceed to |
|---|---|
| LH side rear turn signal light does not illuminate | A |
| RH side rear turn signal light does not illuminate | B |
| B | | GO TO STEP 5 |
|
| 2. | CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - REAR LIGHT ASSEMBLY LH) |
(a) Disconnect the S31 rear combination light assembly LH connector.
(b) Disconnect the Z21 rear light assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S31-5 (TRN1) - Z21-4 (TRN4) | Always | Below 1 Ω |
| S31-5 (TRN1) or Z21-4 (TRN4) - Body ground | Always | 10 kΩ or higher |
| S31-6 (TRN2) - Z21-5 (TRN3) | Always | Below 1 Ω |
| S31-6 (TRN2) or Z21-5 (TRN3) - Body ground | Always | 10 kΩ or higher |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 3. | CHECK REAR COMBINATION LIGHT ASSEMBLY LH |
(a) Interchange the rear combination light assembly LH with RH and connect the connectors.
w/ Rear No. 2 Seat: Click here
w/o Rear No. 2 Seat: Click here
|
| 4. | CHECK OPERATION (REAR TURN SIGNAL LIGHTS) |
(a) Check that the rear turn signal light of the rear combination light assembly LH illuminates.
OK:
The rear turn signal light of the rear combination light assembly LH illuminates.
| OK | | REPLACE REAR LIGHT ASSEMBLY LH |
| NG | | REPLACE REAR COMBINATION LIGHT ASSEMBLY LH |
| 5. | CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - REAR LIGHT ASSEMBLY RH) |
(a) Disconnect the S33 rear combination light assembly RH connector.
(b) Disconnect the Z20 rear light assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S33-5 (TRN1) - Z20-4 (TRN4) | Always | Below 1 Ω |
| S33-5 (TRN1) or Z20-4 (TRN4) - Body ground | Always | 10 kΩ or higher |
| S33-6 (TRN2) - Z20-5 (TRN3) | Always | Below 1 Ω |
| S33-6 (TRN2) or Z20-5 (TRN3) - Body ground | Always | 10 kΩ or higher |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 6. | CHECK REAR COMBINATION LIGHT ASSEMBLY RH |
(a) Interchange the rear combination light assembly RH with LH and connect the connectors.
w/ Rear No. 2 Seat: Click here
w/o Rear No. 2 Seat: Click here
|
| 7. | CHECK OPERATION (REAR TURN SIGNAL LIGHTS) |
(a) Check that the rear turn signal light of the rear combination light assembly RH illuminates.
OK:
The rear turn signal light of the rear combination light assembly RH illuminates.
| OK | | REPLACE REAR LIGHT ASSEMBLY RH |
| NG | | REPLACE REAR COMBINATION LIGHT ASSEMBLY RH |
Daytime Running Light Relay Circuit
Hazard Warning Switch CircuitLexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Rear Door Speaker: Removal
REMOVAL CAUTION / NOTICE / HINT HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG Click here 2. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Transfer Case Front Oil Seal (for Rh Side): Replacement
REPLACEMENT CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transfer case oil seal RH removal/installation are shown below. Necessary Procedures After Parts Rem ...