DESCRIPTION
The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, door side airbag sensor LH and rear airbag sensor LH.
The door side airbag sensor LH and rear airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the door side airbag sensor LH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
| B167A | Front Door Pressure Sensor LH |
|
| Comes on | Does not apply to test/check mode |
| B167E | Front Door Pressure Sensor Threshold Malfunction (LH) |
|
| Comes on | Does not apply to test/check mode |
WIRING DIAGRAM
Click here
CAUTION / NOTICE / HINT
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
PROCEDURE
| 1. | CHECK DOOR SIDE AIRBAG SENSOR LH |
| (a) Turn the engine switch off. |
|
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Interchange the door side airbag sensor LH with RH and connect the connectors.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the engine switch on (IG), and wait for at least 60 seconds.
(f) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs(g) Turn the engine switch off.
(h) Turn the engine switch on (IG), and wait for at least 60 seconds.
(i) Check for DTCs.
Body Electrical > SRS Airbag > Trouble CodesHINT:
Codes other than DTCs B166C, B166F, B167A and B167E may be output at this time, but they are not related to this check.
| Result | Proceed to |
|---|---|
| DTC B167A or B167E is output. | A |
| DTC B166C or B166F is output. | B |
| DTCs B166C, B166F, B167A and B167E are not output. | C |
(j) Turn the engine switch off.
(k) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(l) Return the door side airbag sensor LH and RH to their original positions and connect the connectors.
| A | | REPLACE AIRBAG SENSOR ASSEMBLY |
| B | | REPLACE DOOR SIDE AIRBAG SENSOR LH |
| C | | USE SIMULATION METHOD TO CHECK |
P Seat Airbag Active Mode Indicator (B1660)
Lost Communication with Front Door Pressure Sensor LH (B167B,B167C)Lexus RX (RX 350L, RX450h) 2016-2026 Owners Manual > Intelligent Clearance Sonar
(ICS): Intelligent Clearance Sonar function
If the Intelligent Clearance Sonar function detects that a collision with a
wall or
other stationary object is possible, the hybrid system output will be restricted
to
restrain any increase in the vehicle speed. (Hybrid system output restriction
control:
See A below.)
Additionally, if the ...
Lexus RX (RX 350L, RX450h) 2016-2026 Repair Manual > Telematics System: Data List / Active Test
DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not. HINT: Using the Techstream to read the Data List allows the values or states of ...