PROBLEM SYMPTOMS TABLE
HINT:
| Symptom | Suspected Area | Link |
|---|---|---|
| System does not operate at all | Proceed to "Power Source Circuit" | |
| CAN communication system | | |
| Blind spot monitor sensor LH | | |
| System cannot be turned off | CAN communication system | |
| Blind spot monitor sensor LH | | |
| "BSM not available" or "Check BSM System" is displayed on the multi-information display | Check abnormality history | |
| Blind spot monitor sensor RH | | |
| Blind spot monitor sensor LH | | |
| Combination meter assembly | |
| Symptom | Suspected Area | Link |
|---|---|---|
| Outer rear view mirror indicator RH does not illuminate | Proceed to "Blind Spot Monitor Beam Axis Confirmation" | |
| Outer mirror RH | | |
| Outer mirror control ECU assembly RH | | |
| Outer mirror actuator assembly RH | | |
| Blind spot monitor sensor RH | | |
| Outer rear view mirror indicator LH does not illuminate | Proceed to "Blind Spot Monitor Beam Axis Confirmation" | |
| Outer mirror LH | | |
| Outer mirror control ECU assembly LH | | |
| Outer mirror actuator assembly LH | | |
| Blind spot monitor sensor LH | | |
| Outer rear view mirror indicator RH remains illuminated | Proceed to "Blind Spot Monitor Beam Axis Confirmation" | |
| Blind spot monitor sensor RH | | |
| Outer rear view mirror indicator LH remains illuminated | Proceed to "Blind Spot Monitor Beam Axis Confirmation" | |
| Blind spot monitor sensor LH | | |
| Outer rear view mirror indicator RH does not flash | Proceed to "Turn Signal Light" in Problem Symptoms Table for the Lighting (EXT) section*1 | |
| Proceed to "Turn Signal Light" in Problem Symptoms Table for the Lighting (EXT) section*2 | | |
| Blind spot monitor sensor RH | | |
| Outer rear view mirror indicator LH does not flash | Proceed to "Turn Signal Light" in Problem Symptoms Table for the Lighting (EXT) section*1 | |
| Proceed to "Turn Signal Light" in Problem Symptoms Table for the Lighting (EXT) section*2 | | |
| Blind spot monitor sensor LH | | |
| Outer rear view mirror indicator RH continues to flash | Blind spot monitor sensor RH | |
| Outer rear view mirror indicator LH continues to flash | Blind spot monitor sensor LH | |
| Symptom | Suspected Area | Link |
|---|---|---|
| Function does not operate at all (Blind spot monitor function operates normally) | Data List / Active Test (Reverse) | |
| Automatic transmission system (U881E) | | |
| Automatic transmission system (U881F) | | |
| Blind spot monitor sensor RH | | |
| When shift lever is in R, detection operation is normal but RCTA indicator does not appear on multi-display assembly | CAN communication system | |
| Parking assist ECU*3 | | |
| Radio receiver assembly | | |
| Blind spot monitor sensor LH | | |
| Blind spot monitor sensor RH | | |
| Multi-display assembly | |
Operation Check
Terminals Of EcuLexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Rear Bumper (w/o Rear No. 2 Seat): Components
COMPONENTS ILLUSTRATION *1 QUARTER OUTSIDE MOULDING SUB-ASSEMBLY LH *2 QUARTER OUTSIDE MOULDING SUB-ASSEMBLY RH *3 REAR BUMPER ASSEMBLY *4 REAR LIGHT COVER LH *5 REAR LIGHT COVER RH - - ILLUSTRATION *A for TMC Made *B for TMMC Made *C w/ Intuitive Par ...
Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Camshaft Oil Control Solenoid (for Bank 2): On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (a) Connect the Techstream to the DLC3. (b) Start the engine. (c) Turn the Techstream on. (d) Inspect the camshaft timing oil control solenoid assembly (for intake side). (1) Enter the following menus: Powertrai ...