Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual: Installation

Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual / Brake / Brake (front) / Front Brake Flexible Hose / Installation

INSTALLATION

CAUTION / NOTICE / HINT

NOTICE:

  • Because the left and right front flexible hoses are not interchangeable, verify the part number when installing the front flexible hoses.
  • When reusing the front flexible hoses, use the identification marks created during removal to install each front flexible hose to its original position.

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. INSTALL FRONT FLEXIBLE HOSE

NOTICE:

When installing the front flexible hose, minimize twisting of the hose.

(a) Install a new clip to the front flexible hose.

NOTICE:

  • Install the clip as far as it will go.
  • When installing the front flexible hose, face the identification mark to the outside of the vehicle.

*a

Identification Mark

*b

Torque Wrench Fulcrum Length

*c

Union Nut Wrench

(b) Using a union nut wrench, connect the brake line to the front flexible hose while holding the front flexible hose with a wrench.

Torque:

Specified tightening torque :

15.2 N·m {155 kgf·cm, 11 ft·lbf}

NOTICE:

  • Do not kink or damage the brake line.
  • Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here

  • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

    13.38 N*m (136 kgf*cm, 10 ft.*lbf)

(c) Engage the 2 hooks to install the sensor clamp bracket.

NOTICE:

Do not twist the front speed sensor wire harness when installing it.

Hook

(d) Install the front flexible hose to the shock absorber assembly with the bolt.

Torque:

18.8 N·m {192 kgf·cm, 14 ft·lbf}

NOTICE:

Do not twist the front flexible hose when installing it.

(e) Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:

30.4 N·m {310 kgf·cm, 22 ft·lbf}

NOTICE:

  • Install the front flexible hose lock securely into the lock hole in the front disc brake cylinder assembly.
  • Do not twist the front flexible hose when installing it.

2. BLEED BRAKE LINE

Click here

3. INSTALL FRONT WHEEL

Click here

    Removal
    REMOVAL CAUTION / NOTICE / HINT NOTICE: If both left and right front flexible hoses are disconnected at the same time, be sure to place an identification mark on each hose to indicate its installation ...

    Front Disc Brake Pad
    ReplacementREPLACEMENT CAUTION / NOTICE / HINT NOTICE: After replacing the front disc brake pads, the brake pedal may feel soft due to clearance between the front disc brake pads and front disc. Depre ...

    Other materials:

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Cylinder Block: Disassembly
    DISASSEMBLY CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below. Necessary Procedure After Parts Removed/Installed ...

    Lexus RX (RX 350L, RX450h) 2016-2025 Repair Manual > Power Steering Ecu: Installation
    INSTALLATION PROCEDURE 1. INSTALL POWER STEERING ECU ASSEMBLY NOTICE: Do not drop the power steering ECU assembly, strike it with tools or subject it to impacts. If the power steering ECU assembly is subjected to an impact, replace it with a new one. Do not pull the wire harness of the power ...

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Owners Manual

    Lexus RX (RX 350L, RX450h) 2016-{YEAR} Repair Manual

    © 2025 Copyright www.lexusrx.net
    0.0112